Stellar Industries SI-75 Bedienungsanleitung Seite 93
- Seite / 94
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Replacement Parts
Chapter 9 - Replacement Parts
Hydraulic Components
Part number Description
15463 Thermo Sight gauge
45074 Breather cap - Fill neck
15464 Tank cover - Clean out
C6327 Filter strainer
45332 Filter element
45503 Relief valve
45343 Cylinder 6.00" x 72.00" Lift
45749 Cylinder seal kit (45343) 6.00 x 72.00
45737 Cylinder - Telescopic 5.50" x 185.75" Lift
48967 Cylinder seal kit (45737) 5.50" x 185.75"
45243 Cylinder - Standard Reeving model 174 & 182 SI60 7.00" X 80.00"
45306 Cylinder seal kit (45243 & 45349) 7.00" x 80.00" 174, 182, & 194
45349 Cylinder - Long Reeving model 194 SI60 7.00" X 80.00" Long
46153 Cylinder - Tail Extension SI60 IOX model hoists 3.50" x 40.00"
51070 Cylinder seal kit (46153) 3.50" x 40.00"
45611 Cylinder - Tail Extension SI60 ORX model hoists 3.50" x 80.00"
51071 Cylinder seal kit (45611) 3.50" x 80.00"
Cable Hoist Components
Part number Description
45372PC Collar retaining 2.75x2.03x0.75
0427 Machine Washer 2.00ID 10ga.
1589 Machine Washer 3.00ID 14ga.
C1592 Grease Zerk 1/8 NPT straight
45373 Roller 4.00" outside SI60
45564 Roller - Rear Assembly SI60
45304 Roller 6.00" SI60 Inside
45481 Shaft - Vertical sheave
45523 U-Bolt Clamp 0.88" SI60
46905 U-Bolt Clamp 1.00" SI75
45556 Cable asm - Reeving cylinders 0.88" x 71 ft
45500 Cable asm - Reeving cylinders 0.88" x 81 ft
45410 Cable end casting SI60
45411 Cable end - 0.88"
46604 Cable end - 1.00"
42393 Spring
45114 Reeving Sheave weldment SI60
46712 Reeving Sheave weldment SI75
45138 Pin sheave and cable shaft
45139 Sheave 10" - cable asm SI60
45583 Strap weldment cylinder reeving SI60
49565 U-Bolt 0.50" x 6.75"w x 7.88"
47277 Removable stop - OR model Cable hoists
47276 Removable stop - OR model Cable hoists
47272 Intermediate stop - IO Fold down stop
45621 Intermediate stop - OR Fold down stop
Chassis Mounted Components
Part number Description
45600 Mount Brkt - Truck frame lug SI60
47531 Pin - Pivot
45144 Pin - 2.50" drop shaft SI60
45756PC Collar 2.51x3.25x1.50 w/hole
Controller & Electrical Components
Part number Description
46734 Controller - Straight No Lock
42399 Controller - Joystick
47471 Controller - Pnuematic
49580 Controller - 2 section Pnuematic
45159 Air Actuator (V42)
45798 Handle kit - 2 section VB
D1810 Air Line for air controllers
45907 Switch - Remote SI60
45908 Light - Dump up
46658 Control Cable 108"
46713 Control Cable 156"
47284 Control Cable 252"
46291 Cable connection kit (V20)
Rear Bumper Components
Part number Description
13143 Light - Stop/Turn/Tail 4" Round LED
27626 Light - Back up LED
13145 Light - Clearance (Red) 2" Round LED
13144 Light - Clearance (Amber) 2" Round LED
2320 Light - License plate
18742 Back up Alarm
45813PC Flat link - ICC Bumper
45815PC Spacer 1.25"OD x 0.75"ID x 2.16"
46810 Pin snap lock - 1.00" ICC Heavy duty bumper
Under Body Tool Box Components
Part number Description
23759 Latch - Door
23764 Latch Gasket - Door
33914 Door roller asm for 1 side Includes 4110, 22045, 4166, 4659
4410 Roller OH door
22045 Bracket - Roller OH door
4166 Cap Screw - Shoulder 0.38"
4659 Nut - Center lock 0.38"
4183 Angle - UHMW RH
4167 Angle - UHMW LH
Fender Components
Part number Description
46626 Fender Weldment - Standard 48"
46121 Fender Weldment - Steel Tandem SI60
45567 Fender - Tandem Poly SI60 Half
45891 Fender - Tri-Axle Middle section Poly
45890 Fender - Tri-Axle Front & Rear sections Poly
C4821 Mud Flap 24.00" x 24.00" Stellar
- 1
- Table of Contents 3
- Attention! 4
- Introduction 5
- Chapter 1 - Safety 7
- ATTENTION 8
- Chapter 2 - Operation 9
- Cable Hoist Check List 10
- Loading Operation 11
- Operation 13
- Hoist Prop Operation 15
- Chapter 3 - Maintenance 17
- Inspection of Sheaves 18
- Cable Replacement 19
- Greases Not Recommended 20
- Greases Recommended 20
- Chapter 4 - Specifications 21
- Cable Hoist Dimensions 22
- Container Subframe 23
- Chapter 5 - Decals 25
- Safety Decals of Note 26
- Chapter 6 - Installation 27
- Cab Boundary 28
- Dimensions: 174 Models 29
- Dimensions: 182 Models 30
- Dimensions: 194 Models 31
- Step 2: Mount Hoist 32
- Step 3: Mount Lift Cylinders 33
- 0.38 4-7.63 34
- Figure C 34
- 35
- FRAME RAIL 35
- Hex. Slot 38
- Step 10: Bumper Installation 40
- Installation 41
- Installed 42
- Locate bracket on hoist base 42
- Steel Tandem/Tri-Axle 43
- Plastic Tandem/Tri-Axle 44
- End of Torch 45
- Cut Slot 45
- PN 45621 46
- O.R. Fold Down Stop 46
- I.O. Fold Down Stop 46
- REF. ANSI Standard 47
- Z245.1-1999 47
- Z.2.16 Vehicle Conspicuity 47
- Hydraulic Schematic 49
- Standard Cylinder Mount 50
- Telescopic Cylinder Mount 51
- Reverse Cylinder Mount 52
- PN 56094 54
- Reeving Cylinder 55
- Electrical Schematics 58
- Chapter 8 - Assembly Drawings 59
- Air Controllers Assembly 1 60
- 2 Section Air 61
- PN 45833 61
- 3 Section Air 61
- PN 46638 61
- Main Hoist Assembly 62
- PN 60221 63
- Chassis Mounted Parts 64
- PN 55261 66
- PN 55265 68
- Cab Guard - PN 47263 69
- PN 46579 70
- Reservoir Assembly - PN 46133 71
- PN 45710 72
- PN 46642 73
- For Reservior 74
- PN 45887 75
- PN 46818 76
- PN 53397 77
- ICC Wide Bumper - PN 53397 77
- PN 46809 78
- Assembly Drawings 79
- PN 48846 80
- ICC Narrow Bumper - PN 48846 81
- PN 62663 82
- Tri-Axle Fenders - PN 46299 83
- PN 46122 84
- Assembly Drawings 85
- PN 45893 87
- PN 55262 88
- NOTE: SEAL KIT P/N 45306 89
- NOTE: SEAL KIT P/N 51070 90
- Ratchet Strap Kit - PN 63150 91
- PN 42918 92
- Chapter 9 - Replacement Parts 93
- Revision Date: February 2010 94
- Document Number: 37040 94
Verwandte Produkte und Handbücher für Nein Stellar Industries SI-75
Nein Stellar Industries 7628 Bedienungsanleitung
(30 Seiten)
(30 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern